Содержание


Factory audio component removal

Radio head unit Infinity amp Dash speakers
Front speakers Rear speakers CD Changer



Radio head unit
AM/FM Cassette  •  AM/FM/CD  •  AM/FM/Cassette/CD

radio removal
radio removal 2
radio removal 3

  • The radio/vent trim bezel is held in place with 4 spring clips. With a wide flat tool (a 3" plastic spackle tool works great), gently pry on each vertical side and carefully pull the bezel out a little at a time until it is free. The red areas in the center picture are the felt-lined receptacles that the bezel spring clips fit in to, which shows the general area of where to pry when removing the bezel.

  • The radio is secured with four phillips screws, one in each corner.

  • Slide the radio straight out and remove two wire harnesses and antenna connector on the back.

radio head unit
radio back
2002 AM/FM/Cassette/CD Head unit, front and back. The wiring connectors were changed for 2002.




Infinity GoldTM amplifier
6-channel, 180-watts

Infinity amp
Infinity Gold amp
Infinity amp

  • Located under the rear passenger-side seat, removal of the Infinity amplifier is pretty much self-explanatory. Four nuts to remove, and two wire harnesses to unplug. The photo at far right shows the simple circuit board of the Amp, the only component inside the unit.




Dash speakers
2.5" tweeters

front dash trim remove
front tweeter
front tweeter

  • With a wide flat tool (3" plastic putty knife or similar, as shown in upper left photo), gently pry the dash trim panel upwards starting at either end. You can then get your fingers under the lip and lift it up, working your way to the opposite end. The trim is held in place by four spring clips. There are no parts or wires attached to the trim cover.

  • The tweeters are held in place by 2 phillips screws. You'll need a very short or angled screwdriver to remove them.

dash trim cover
tweeter grill
Upper dash trim cover showing tweeter location and close-up of tweeter grill


  • Speaker opening: 3-3/4" x 2-3/4+"
  • Speaker opening depth: 1-3/4"
  • Factory speaker thickness: 1-3/8"
  • Factory speaker diameter: 2-1/2"
  • Distance between screws: 3-11/32"
  • Factory speaker part #: 56038411AC
 




Front door speakers
6"x9" full-range (standard) / 6"x9" woofer (Infinity)

driver door speaker

  • Speaker cut-out opening: 8-1/2" x 5-3/4"
  • Speaker opening depth (to glass): 2-7/8"
  • Factory speaker mounting depth: 2-11/16"
  • Factory speaker thickness: 3-5/16"
  • Factory speaker size: 9-1/8" x 6-5/16"
  • Distance between screws: 6-9/16" & 4-5/8"
  • Factory speaker part # (Infinity): 56038656AA
front door speaker opening
 
front door speaker




Rear door speakers
6.5" round full-range

rear door speaker

  • Speaker cut-out opening: 5-3/4" diameter
  • Speaker opening depth (to glass): 2-7/8"
  • Factory speaker mounting depth: 1-7/8"
  • Factory speaker thickness: 2-9/16"
  • Factory speaker size w/grill: 6-3/4"
  • Distance between screws: 6-1/2"
  • Factory speaker part # (Infinity): 56038657AA
rear door speaker opening
 
rear door speaker




10-Disc CD changer

CD changer 4
CD changer 5
CD changer 6

  • Open lid and remove 4 the phillips head screws that run along the top edge of the compartment hinge. Lift compartment housing straight up an inch or so until it stops and then pull straight out to remove.

  • Remove 6 phillips screws that attach changer to bracket, 3 on each side. A very short or angled screwdriver is needed for one screw on each side. Unhook wire connector on left side. The unit can now be slid out away from the bracket.

  • The factory support bracket is attached with 6 nuts.


CD changer unit

CD Changer compartment
Location: Passenger side cargo area
CD changer unit

CD Changer unit. Part # P56042129AG.
Dimensions: 10-3/4" W x 7" H x 3" D.


CD changer unit

CD Changer compartment cover backside view







Содержание